The cable provided is compatible with my Flysky i6 Tx for simulation on FPV Freerider

The cable provided is compatible with my Flysky i6 Tx for simulation on FPV Freerider

The cable provided is compatible with my Flysky i6 Tx for simulation on FPV Freerider

As others have said, this works great with the I6. To get this working correctly, I set the toggle on the dongle to "G5-G7 Above", plugged the cable into the port on the backside of the TX, and set the TX to "Student Mode". Make sure to check your control panel's "devices and printers" section to see if a gaming controller is present. To set your I6 in student mode, turn the power switch off and hold the two bottom trim buttons inward, and then proceed to toggle the power on. After it has powered on, release the trim buttons and hold the "OK" button to access the menu. The rest should be straight forward. Note that I have not been able to get the TX to be recognized with the I6 programmer to flash the firmware. If anyone has any luck with that, please comment.

As others have said, this works great with the I6. To get this working correctly, I set the toggle on the dongle to "G5-G7 Above", plugged the cable into the port on the backside of the TX, and set the TX to "Student Mode". Make sure to check your control panel's "devices and printers" section to see if a gaming controller is present. To set your I6 in student mode, turn the power switch off and hold the two bottom trim buttons inward, and then proceed to toggle the power on. After it has powered on, release the trim buttons and hold the "OK" button to access the menu. The rest should be straight forward. Note that I have not been able to get the TX to be recognized with the I6 programmer to flash the firmware. If anyone has any luck with that, please comment.

As others have said, this works great with the I6. To get this working correctly, I set the toggle on the dongle to "G5-G7 Above", plugged the cable into the port on the backside of the TX, and set the TX to "Student Mode". Make sure to check your control panel's "devices and printers" section to see if a gaming controller is present. To set your I6 in student mode, turn the power switch off and hold the two bottom trim buttons inward, and then proceed to toggle the power on. After it has powered on, release the trim buttons and hold the "OK" button to access the menu. The rest should be straight forward. Note that I have not been able to get the TX to be recognized with the I6 programmer to flash the firmware. If anyone has any luck with that, please comment.

USB dongle works witch Eachine i6 (From RTF kit Falcon 250 Pro). By default Eachine i6 doesn not send PPM signal on "trainter" connector on the back, so every time when you want to use simulator you need set in transmitter menu an option "Student mode". On this USB cable set second option "G5-G7 Above". It work for me with Freerider on Android an on Mac Os X without any additional drivers.

USB dongle works witch Eachine i6 (From RTF kit Falcon 250 Pro). By default Eachine i6 doesn not send PPM signal on "trainter" connector on the back, so every time when you want to use simulator you need set in transmitter menu an option "Student mode". On this USB cable set second option "G5-G7 Above". It work for me with Freerider on Android an on Mac Os X without any additional drivers.

USB dongle works witch Eachine i6 (From RTF kit Falcon 250 Pro). By default Eachine i6 doesn not send PPM signal on "trainter" connector on the back, so every time when you want to use simulator you need set in transmitter menu an option "Student mode". On this USB cable set second option "G5-G7 Above". It work for me with Freerider on Android an on Mac Os X without any additional drivers.

All the supplied software works with the simulator cable. RealFlifht G7 PhoenixRC X5 Aerofly Reflex XTR and VRC Installed everything without any problem. Only one issue - the sticker says about 5 positions of the switch, but actually there are 4 (the 5th position is VCR2). But nevertheless it is the best value of money! Highly reccomend

All the supplied software works with the simulator cable. RealFlifht G7 PhoenixRC X5 Aerofly Reflex XTR and VRC Installed everything without any problem. Only one issue - the sticker says about 5 positions of the switch, but actually there are 4 (the 5th position is VCR2). But nevertheless it is the best value of money! Highly reccomend

All the supplied software works with the simulator cable. RealFlifht G7 PhoenixRC X5 Aerofly Reflex XTR and VRC Installed everything without any problem. Only one issue - the sticker says about 5 positions of the switch, but actually there are 4 (the 5th position is VCR2). But nevertheless it is the best value of money! Highly reccomend

ben cok begendim tam flyskya uygun cd nin icinde uygulamalarda var. kargo 8 gundr ulasti saka gibi :) cinden mi aliyoz yurt icinden mi belli degil

ben cok begendim tam flyskya uygun cd nin icinde uygulamalarda var. kargo 8 gundr ulasti saka gibi :) cinden mi aliyoz yurt icinden mi belli degil

ben cok begendim tam flyskya uygun cd nin icinde uygulamalarda var. kargo 8 gundr ulasti saka gibi :) cinden mi aliyoz yurt icinden mi belli degil

I got this to practice with simulators before flying the 250 I built. It took a few tries to get things working but no complaints. I'm running Windows 10. Some things to note; Pick an unused model on the transmitter and enable trainer mode. Plug in USB. Make sure your transmitter shows up in devices before launching the sim program. Calibrate. Enjoy!

I got this to practice with simulators before flying the 250 I built. It took a few tries to get things working but no complaints. I'm running Windows 10. Some things to note; Pick an unused model on the transmitter and enable trainer mode. Plug in USB. Make sure your transmitter shows up in devices before launching the sim program. Calibrate. Enjoy!

I got this to practice with simulators before flying the 250 I built. It took a few tries to get things working but no complaints. I'm running Windows 10. Some things to note; Pick an unused model on the transmitter and enable trainer mode. Plug in USB. Make sure your transmitter shows up in devices before launching the sim program. Calibrate. Enjoy!

Он заразил мой компьютер вирусом, который принес симулятор, и теперь его невозможно удалить. Заплати через PayPal, я затребую сумму за тренажер и ущерб, причиненный моему ноутбуку.

Me ha infectado el ordenador con un virus que trae el simulador y ahora no hay manera de eliminarlo. Pague con PayPal, les reclamaré el importe del simulador y los daños ocasionados a mi laptop.

Он заразил мой компьютер вирусом, который принес симулятор, и теперь его невозможно удалить. Заплати через PayPal, я затребую сумму за тренажер и ущерб, причиненный моему ноутбуку.

Очень быстро при доставке в Чили пакет прибыл очень хорошо продукты именно так, как они указывают на своих фотографиях, работая без проблем с Flysky передатчик FS-i6X i6X 10CH

Muy Rápidos en la entrega a Chile el paquete llego muy bien los productos son exactamente como lo indican en sus fotografías ,funcionando sin problemas con Transmisor Flysky FS-i6X i6X 10CH

Очень быстро при доставке в Чили пакет прибыл очень хорошо продукты именно так, как они указывают на своих фотографиях, работая без проблем с Flysky передатчик FS-i6X i6X 10CH

Приказ прибыл через Нинджаван в Сингапур через 10 дней, несмотря на задержку. хорошо работает с phoenixRC на Windows 10 - подключи и играй, не требуется установка драйвера для использования USB-ключа. CD поставляется с полным набором программного обеспечения, и я использовал его для установки phoenixRC 5.0.b Никаких проблем с использованием моего ретуши 9XR. Испробовал оба порта JR и Futaba на моем tx и они работают безупречно. Тем не менее, калибровка регуляторов на phoenixRC была довольно сложной... я должен был убедиться, что все палочки (включая дроссель) были сосредоточены, прежде чем войти на страницу калибровки, иначе мой дроссельный канал будет регистрировать 100% вход, когда палочки превышают 50%. В целом очень довольны!

order arrived in 10 days via ninjavan to singapore despite covid delay. works well with phoenixRC on windows 10- plug and play, no driver installation needed to use the USB dongle. included CD comes with a whole suite of software, and I used that to install phoenixRC 5.0.b no issues using with my turnigy 9XR. tried both the JR and futaba ports on my tx and they work flawlessly. however, calibrating the controls on phoenixRC was quite tricky...i had to make sure all sticks(including throttle) were centred before entering the calibration page otherwise my throttle channel will register 100% input whenever the sticks are beyond 50%. overall very satisfied!

Приказ прибыл через Нинджаван в Сингапур через 10 дней, несмотря на задержку. хорошо работает с phoenixRC на Windows 10 - подключи и играй, не требуется установка драйвера для использования USB-ключа. CD поставляется с полным набором программного обеспечения, и я использовал его для установки phoenixRC 5.0.b Никаких проблем с использованием моего ретуши 9XR. Испробовал оба порта JR и Futaba на моем tx и они работают безупречно. Тем не менее, калибровка регуляторов на phoenixRC была довольно сложной... я должен был убедиться, что все палочки (включая дроссель) были сосредоточены, прежде чем войти на страницу калибровки, иначе мой дроссельный канал будет регистрировать 100% вход, когда палочки превышают 50%. В целом очень довольны!

This simulator cable works great with a FlySky FS-I6x and FPV Freerider on Arch Linux. Just set switch to position 2 "G5-G7 Above", attached transmitter cable, turned on transmitter, cenetered sticks, plugged into USB port and started FPV Freerider. Cable lenght is perfect. It will quickly pay for it's in saved props. Just buy it. :) I'm happy I did.

This simulator cable works great with a FlySky FS-I6x and FPV Freerider on Arch Linux. Just set switch to position 2 "G5-G7 Above", attached transmitter cable, turned on transmitter, cenetered sticks, plugged into USB port and started FPV Freerider. Cable lenght is perfect. It will quickly pay for it's in saved props. Just buy it. :) I'm happy I did.

This simulator cable works great with a FlySky FS-I6x and FPV Freerider on Arch Linux. Just set switch to position 2 "G5-G7 Above", attached transmitter cable, turned on transmitter, cenetered sticks, plugged into USB port and started FPV Freerider. Cable lenght is perfect. It will quickly pay for it's in saved props. Just buy it. :) I'm happy I did.